卷 6, 编号 2-2 (2012)
- 年: 2012
- 文章: 67
- URL: https://journals.rcsi.science/2074-0530/issue/view/3763
Articles
Tangential oscillations with combination of cutting and surface plastic deformation of flexible shafts
摘要
The article describes the stages of combined devices for cutting-deformed processing design of non-rigid shafts.
Izvestiya MGTU MAMI. 2012;6(2-2):7-10
7-10
Sintered metal alloys for high-loaded contacts of ignition system of internal combustion engine
摘要
This paper presents an experimental investigations of alloying elements and structure influence on the physico-mechanical properties of ceramic-metal tungsten alloy with the addition of nonstoichiometric compounds of rare-earth metals. The paper illustrates the application of tungsten alloys with yttrium oxide as a material for high-loaded contact of ignition internal combustion engines system.
Izvestiya MGTU MAMI. 2012;6(2-2):10-14
10-14
Statistical modeling of the output parameters in process of machining of ceramic composite materials with using bound-abrasive
摘要
The article describes theoretical and experimental results of the statistical simulation of ceramics after treatment using bound-abrasive АС4 63/50 processes. The article presents statistical equations with a subsequent decrease of the problem dimension with the aim of adequate analysis of the studied patterns. The experimental dependence of the output process indicators are described (removal rate and surface roughness) in the field of statistical optimum response function when processing ceramics VK-100 using the method of finishing with the help of bound-abrasive.
Izvestiya MGTU MAMI. 2012;6(2-2):14-21
14-21
Used automotive catalysts as major sources of secondary precious metals
摘要
Used automotive catalysts are the major sources of secondary precious metals. The analysis of hydrometallurgical and pyrometallurgical technologies of extracting the precious metals from disposed automotive catalysts was made. The reasonability of use for utilization of new catalyst generation on metal transmitter of collector melting in plasma-arc furnace using self-generated steel manifold is introduced. We have outlined the directions of research works on a substantiation of process of autocatalysts utilization parameters.
Izvestiya MGTU MAMI. 2012;6(2-2):21-25
21-25
Integrated use of all secondary resources as the strategic goal of car utilization
摘要
The article considers the problems of automobile utilization. The paper describes that the recyclable car is the source of not only secondary ferrous and non-ferrous alloys, but also a variety of non-metallic construction materials: plastics, rubber, textiles, glass, etc., which rational use is possible only at regulated disassembly of the vehicle.
Izvestiya MGTU MAMI. 2012;6(2-2):25-30
25-30
High precision machining of hardened steels using small-sized tools of cubic boron nitride
摘要
The paper considers the ways of product processing with nanoscale accuracy using small-sized cutting tools with mechanical fixing of cubic boron nitride plates.
Izvestiya MGTU MAMI. 2012;6(2-2):30-38
30-38
Formation of roughness of the surface layer of non-rigid parts of hollow cylinder type during combined machining and surface plastic deformation
摘要
The forming of surface roughness of non-rigid parts such as hollow cylinder while combined machining intervenes three phases. The magnitude of surface roughness depends on shape and size of deformed elements, magnitude of axial feed, radial forcing, number of stressing cycles, physical and mechanical parameters of the material, etc.
Izvestiya MGTU MAMI. 2012;6(2-2):38-41
38-41
Material prerequisites for the creation of machine-building products of new generation
摘要
The creation of fundamentally new engineering products is impossible without materials, whose characteristics are many times higher than the world average. However, the traditional technologies of hardening materials have exhausted their potential. The output from the impasse of technology is based on using possibilities of nano-sized states of substance that was implemented on example of system of carbon-carbon. The proposed technology can be modified for creating of nanomaterials with characteristics that are many times higher than the achieved level of other chemical raw materials using gas-, liquid-and solid-phase crystallization processes.
Izvestiya MGTU MAMI. 2012;6(2-2):41-51
41-51
Analysis of machinability of steel 75HGFC
摘要
The article considers character of the consumption of many-sided non-re-sharpened carbide inserts during the whetting of experimental high carbon alloy steel 75HGFC. There are made recommendations for choice of plate forms, corners of a cutting part and the type of wear-resistant coatings rear and front surfaces.
Izvestiya MGTU MAMI. 2012;6(2-2):51-55
51-55
Technique of definition the complexity of castings by design and technological parameters of a cast part
摘要
During the production of castings there are often appear the problems connected with complexity of their manufacturing. They carry both technical, and economic character. As a rule, in conditions of production, these tasks are solved on the basis of the practical experience based on subjective character at their assessment. In this article authors, leaning on the principles which are put at the beginning of these works, offer a technique by determination of casting complexity, irrespective of a way of their manufacturing on constructive and technological parameters of a cast detail. Estimated criteria of their definition were developed for each of groups.
Izvestiya MGTU MAMI. 2012;6(2-2):55-61
55-61
Primenenie fraktal'nogo analiza dlya opisaniya i otsenki stokhasticheski sformirovannykh poverkhnostey
摘要
In the article on the example of the 1201 alloy, is proposed a new approach for the description and evaluation of stochastically generated surfaces, based on fractal analysis. The results of investigation of the interrelation between the numerical values of the fractal dimension and the parameters of the technology of the dimensional electrochemical machining are presented.
Izvestiya MGTU MAMI. 2012;6(2-2):61-64
61-64
Features of mechanical treatment of parts of ceramic materials
摘要
The article shows the peculiarities of diamond grinding of parts made of ceramic materials and proposed new directions of the research of improving the quality of ceramic details surfaces.
Izvestiya MGTU MAMI. 2012;6(2-2):64-67
64-67
Technology of processing of complex shape products (on the example of gas-turbine engine mono-wheel blades)
摘要
The article considers industrial experience of processing of monowheels blades of gas-turbine engines, analyses characteristics, merits and demerits of ways of processing, the conclusion is drawn on carrying out further researches by authors.
Izvestiya MGTU MAMI. 2012;6(2-2):67-73
67-73
Electromagnetic field of the hybrid car
摘要
Analysis and evaluation of the sources of electromagnetic fields of the car will allow to solve a fundamentally new tasks on reduction of negative influence of these fields on humans and the environment.
Izvestiya MGTU MAMI. 2012;6(2-2):73-76
73-76
Influence of the mode parameters on the technological characteristics of the injector hole broaching operation
摘要
Influence of the pulse duration on the machining time and instrument wear touching the electroerrosion drilling of the little diameter holes on the special machine tool is shown experimentally in this paper. The dependence between speed of erosion and hole depth is investigated. The statistical regularity of distribution operation time and the instrument wear speed is revealed. Engineering solutions for a higher stability drilling of the holes are proposed.
Izvestiya MGTU MAMI. 2012;6(2-2):77-83
77-83
Models for calculation of thermal displacements of spindle assemblies
摘要
The description of the semi-empirical models developed on the basis of results of theoretical and pilot studies is provided in article, for calculation of thermal offsets of spindle blocks at the most characteristic modes of operation of lathes.
Izvestiya MGTU MAMI. 2012;6(2-2):83-86
83-86
Analysis of multilayer material producing and prospects of using of nonequal-thick sheet material
摘要
The article describes the methods of producing of multilayer materials and their properties.
Izvestiya MGTU MAMI. 2012;6(2-2):86-91
86-91
Application of laser welding technology in manufacture of pressure vessels of titanium alloy
摘要
Some features of the reducing of weight and size of high pressure vessels (HPV) with using of a thin-walled metal shell-liner from titanium alloy VT-1,0 are considered in this paper. The main difficulties are encountered under the manufacture of welded titanium alloy liner VT-1,0. There are presented the results of the selection of welding titanium alloy VT-1,0, shown the influence of technology of edge preparation on the quality of welded joints as well as the possibility of using laser welding technology in the liner of the VT-1,0.
Izvestiya MGTU MAMI. 2012;6(2-2):91-94
91-94
Determination of metals plasticity by combined cross-extrusion and upset
摘要
The paper proposes a new method for constructing the plasticity curve using the method of the combined cross-extrusion and upset. There is ensured uniform strain on the side of collar. There are eliminated a shear component and the strain tensor.
Izvestiya MGTU MAMI. 2012;6(2-2):95-98
95-98
Calculation and optimization of the welded frame for unique machine-tools
摘要
Nowadays, when the production of cutting machines is realized by single or small-serial lots, the topical problem is the transition of base parts of machine-tools from cast to welded modification. However, the absence of experimentally-tested method, allowing to produce calculations and the optimization of welded base details, depending on particular conditions in every particular situation, suspends the process of their widespread introduction to machine-tool industry.
Izvestiya MGTU MAMI. 2012;6(2-2):98-104
98-104
Theoretical studies of dependence of geometric parameters of a contact between a tool and a workpiece on installation of a tool in the process of burnishing
摘要
The article describes theoretical studies of the dependence of geometric parameters of a contact between a tool and a workpiece on the installation of a tool in the process of burnishing. Lathe plates of standard geometry (SNMG) were considered as tools. Modeling of contact interaction was performed in the software environment KOMPAS 3D. There are presented and analyzed the relations based on theoretical research.
Izvestiya MGTU MAMI. 2012;6(2-2):104-109
104-109
Forming processes when machining of a solid of revolution by external broach
摘要
The article describes forming process when machining of a solid of revolution by external broach.
Izvestiya MGTU MAMI. 2012;6(2-2):109-112
109-112
Designing of the technological process for manufacturing of parts based on technical and economic modeling
摘要
In this article there is considered the problem of finding a method of machining, which has optimal technical and economic parameters such as: basic (machine) time, performance, cost, profit, in close connection with the designing of optimal process.
Izvestiya MGTU MAMI. 2012;6(2-2):112-116
112-116
Venture companies in modern mechanical engineering production
摘要
The aim of proposed approach is to reduce the cost and terms of products manufacturing by rational load of existing production systems while ensuring a given quality of manufactured products.
Izvestiya MGTU MAMI. 2012;6(2-2):116-118
116-118
Methods of comparative evaluation of cost and quality of innovative solutions in the project life cycle of high-tech products of mechanical engineering production
摘要
In the article there is considered the technique of comparative evaluation of the cost and quality of high-tech innovation of engineering products at the project preparation stage of production using linear mathematical models. Developed analytical models are descriptive, universal and can be automated with the use of tools of personal computers.
Izvestiya MGTU MAMI. 2012;6(2-2):118-124
118-124
Efficiency improvement of multi-axis milling of complex surfaces on CNC machines
摘要
In this article there are considered the questions of efficiency of multi-axis milling of complicated spatial surfaces on CNC machines. The authors made the visualization of complex spatial surface in the CAD/CAM/CAE/DDM-system of SolidWorks.
Izvestiya MGTU MAMI. 2012;6(2-2):124-128
124-128
Precision of machining on CNC machines
摘要
The authors consider the algorithm of creation of mathematical model of form-building system of CNC machine-tool, allowing to consider errors of positioning of movable objects of the machine with help of introduction of the module of correction in the operating program.
Izvestiya MGTU MAMI. 2012;6(2-2):129-130
129-130
Key problems of manufacturing of solid hard-alloyed end tools on CNC machines
摘要
The authors pointed out the main problems of production of solid carbide end tool and dependence on software-systems (PMC) of foreign suppliers. There are presented layout circuits, design and technological capabilities of CNC tool and cutter grinding machine.
Izvestiya MGTU MAMI. 2012;6(2-2):130-134
130-134
Importance of simplicial sets in quality management of technical products
摘要
The paper shows the potential of simplicial sets of topological spaces in the quality management of technical products. At the same time the authors describe the basic issues of definition of main products required in estimating the level of quality of assessed technical products. Also shown that, as a generalized indicator in determining the quality of basic products based on simplicial sets it is possible to use the newly introduced character m which stands for geometric mean of the parameters of the simplex.
Izvestiya MGTU MAMI. 2012;6(2-2):134-138
134-138
Estimation of CNC machine error influence on precision of machining of surfaces of the body of tool holder for replaceable inserts
摘要
The article examines the influence of errors caused by CNC machines on precision of milling small linear surfaces on the example of machining seats for inserts in the body of a tool holder.
Izvestiya MGTU MAMI. 2012;6(2-2):138-140
138-140
The current state and prospects of ultrasonic dimensional processing in mechanical engineering
摘要
Analysis of the modern technologies and equipment for the ultrasonic dimensional processing is performed in this paper. The authors considered features of the ultrasonic processing of the holes with the tubular diamond tool. There were made the experiments on the upgraded ultrasonic machine 4770 M with application of a special working head with a rotating tool spindle. Optimum conditions of carrying out the process, providing technical requirements to a detail are revealed.
Izvestiya MGTU MAMI. 2012;6(2-2):140-144
140-144
Modern methods of hollow metal microsphere manufacture
摘要
The energy and resource economy are for many countries the key words in there live, which, in case of science, is the intelligence resource application, define the further way of development of technologies. The present paper reveals one of the energy efficient ways of science investigation in light construction of materials. The small hollow spheres made from different materials could change the weight of a construction part essentially, used as acoustic and thermal insulation and also as protection against vibrations and energy, induced by plastic deformation of material. They can be used as a unit cell for big parts and alone filled with an inert gas, e.g. fusion targets. The methods of their production could be divided in chemical, powder and metallurgical. The metallurgical method requires the intelligence application, because it is based on the own properties of the materials and boundary conditions of the process, not involving any organically core and preparation of the powder.
Izvestiya MGTU MAMI. 2012;6(2-2):144-150
144-150
Application of an axisymmetric rigid-plastic finite element membrane model for evaluation of friction coefficients in sheet metal forming processes
摘要
The results of computational and experimental investigations are presented on the application of an axisymmetric rigid-plastic finite element membrane model for evaluation of friction coefficients in sheet metal forming processes. The data on hemispherical punch stretching of a sheet metal under investigation are used. The method's possibilities are demonstrated by examining cases with different friction conditions.
Izvestiya MGTU MAMI. 2012;6(2-2):150-158
150-158
Reliability estimation of lathes with CNC by the accuracy of processing
摘要
The paper presents a method of determining the reliability of the precision CNC lathes with the mutual influence of processes which reduce accuracy machining.
Izvestiya MGTU MAMI. 2012;6(2-2):158-164
158-164
Increase of productivity of processing the pneumo - and hydraulic cylinders by enhancement of the device for combined machining and surface plastic deformation
摘要
A combined treatment of cutting and surface plastic deformation is a highly efficient production process of manufacturing functional surfaces of cylinder bodies and pneumatic and hydraulic cylinders. Indicators discussed in the article are studied by authors patented design of the aforementioned devices.
Izvestiya MGTU MAMI. 2012;6(2-2):164-166
164-166
Enhanced operating characteristics of the scanning magnet controlled ferroimpurities of molding compounds
摘要
The article presents the results of multiple scanning through magnet control of ferroimpurities molding mixtures - in the implementation of large and very large number of control activities. There is detected the «break» each of the massively-operating characteristics of the control, which explain clearly illustrated narrowing of the spectrum of ferroimpurities operational size. the principal (which determines the objectivity of the data control) role of the second, functionally extrapolated sections of the specifications is shown and using the original settlement models quantitatively assessed.
Izvestiya MGTU MAMI. 2012;6(2-2):166-177
166-177
Aspects of ensuring of reliability of crankshaft bearings
摘要
A brief history of the problem of density of planting crankshaft bearings is shown, the results of analysis of the failure of bearings engine KAMAZ-740 in operation are presented. The article examines the results of tests, analyses publications on the problem, proposes a mechanism for violations of the density of planting connecting rod inserts and the refined method of calculation of their landing.
Izvestiya MGTU MAMI. 2012;6(2-2):177-184
177-184
Increasing of cutting efficiency of heat-treated steel through the application of cutting tools of high-strength composite ceramic with coating E. S. Sotova, M. N. Lazareva
摘要
In the paper there is investigated the cutting tool properties of high-strength composite ceramics with multi-coated cutting hardened steel. Mathematical models of cutting are obtained. They establish the dependence of the wear and tear on the back of the instrument, roughness of the machined surface of the parts, the tangent component of the cutting forces, as well as cutting power on the modes of turning. A problem of cutting tools modes optimization is made of high-strength composite ceramics. It is established that the application of the multi-functional coatings on ceramic cutting tool allows you to increase the efficiency of processing.
Izvestiya MGTU MAMI. 2012;6(2-2):184-189
184-189
Virtual coordinate-measuring machine
摘要
The article considers the principles of construction and realization of the virtual coordinate-measuring machine, which allows to develop on the personal computers the control programs for real coordinate-measuring machines not occupying their production time. In the development of virtual coordinate-measuring machine special attention is paid to increase the realism of the simulation of measurements on the screen of your PC and increase the performance of the software modules to create a regime of real time.
Izvestiya MGTU MAMI. 2012;6(2-2):189-193
189-193
Overview of the multi-layer sheet deformable materials for protection against noise
摘要
The article describes the multi-layered deformable materials, which can reduce the noise level. Possibility of deformation of multi-layer billets, which provide a high noise protection and noise insulation, is estimated.
Izvestiya MGTU MAMI. 2012;6(2-2):194-199
194-199
Research of hardened galvanized sheet bending
摘要
A numerical research of the strengthened bending of the sheet was made. A graphical distribution arising in the process of bending stresses is received. The character of changes of bending moment is analyzed and carried out the experimental check of the data received.
Izvestiya MGTU MAMI. 2012;6(2-2):199-204
199-204
Localized bending and twisting of the galvanized strip during formation of channel
摘要
Algorithm for solving the problem of profiling strip with pre-stamped technological groove hub is considered. In the course of deformation analysis of this technology bend in the place of localization and twisting of tuck shelves occurs. There are made comparisons of the calculated and experimental data.
Izvestiya MGTU MAMI. 2012;6(2-2):204-208
204-208
Experimental investigation of the process of extrusion of a technological groove in a galvanized strip
摘要
The research on the definition of accumulated deformations in the zone of embossed roller indenter of technological grooves is made. The peculiarities of distribution of the intensity of deformation are defined. Estimates of the averaged over the cross-section of the groove values base of the deformation intensity were made.
Izvestiya MGTU MAMI. 2012;6(2-2):208-213
208-213
Mechanical processing with activated air
摘要
The method of increase of wear resistance of metal-cutting tools by application of the activated air stream is offered. Results of researches of ozonized air influence on intensity of deterioration fast-cutting and hard alloy tools are presented
Izvestiya MGTU MAMI. 2012;6(2-2):213-216
213-216
New technology of processing of cutting tool by use of activated air
摘要
A method of increasing wear resistance of cutting tools by the application of activated the air flow is introduced. The results of studying the influence of the ozonized air on the intensity of wear of the cutting tool are presented.
Izvestiya MGTU MAMI. 2012;6(2-2):216-218
216-218
Fractal multidimensional scale for controlling of the mode of dimensional electrochemical machining and evaluation of its output data
摘要
The article proposes an updated and expanded version of the previously proposed fractal multidimensional scale, allowing through the fractal dimension to regulate the mode of the dimensional electrochemical machining and evaluate the structural and dynamic characteristics of the processed surface.
Izvestiya MGTU MAMI. 2012;6(2-2):218-222
218-222
Nanodisperse multi-layered composite coatings for cutting tools
摘要
Some aspects of application for multilayered-composite functional coatings with nano-scale grains and layers thickness for various types of the cutting tool are considered. There is shown, that cutting tools with nanoscale structured coatings provide essential increase of cutting efficiency in comparison with standard coated tools of an adequate coating chemical compound.
Izvestiya MGTU MAMI. 2012;6(2-2):222-230
222-230
Highly effective layered tool materials with nano-dispersed multi-layered of wide range of applications
摘要
The paper presents the development of layered composite material, which includes a carbide substrate, a ceramic layer and a nano-scale multilayered coating. Each element of a layered tool material fulfills individual functions. The carbide layer provides raised toughness and strength of tool material, the ceramic layer provides resistance of a tool material to oxidation, corrosion and high-temperature weakening at elevated temperatures, the nano-scale multilayered coating decreases thermal-mechanical stresses on the rake face of the tool and eliminates superficial defects of the ceramic.
Izvestiya MGTU MAMI. 2012;6(2-2):230-238
230-238
Criteria of processing operations optimization of gear-producing based on various methods of tooth formation
摘要
The article considers the block diagram of operations of machining of gear rings. The indicators characterising accuracy and stability of gear- producing operations are offered. There are given proposals on optimisation of technological chains manufacturing of cylindrical gear rings.
Izvestiya MGTU MAMI. 2012;6(2-2):238-242
238-242
Prospects of development and application of physico-chemical methods and technologies in engines manufacture
摘要
The role and importance of non-traditional physical and chemical technologies in science-filled technique production are shown in this paper. The main directions of such technologies and its equipment development are formulized. The basic spheres of the application of electroerrosion, electrochemical and laser machining in the engine production are presented. Efficiency of such technologies using in order to solve new technological problems connected with stock removal nearby 1…30 μm in depth and surface roughness parameter less than Ra = 0,2…0,4 μm.
Izvestiya MGTU MAMI. 2012;6(2-2):242-247
242-247
Status and opportunities for development of some gear cutting technologies and equipment
摘要
The article describes some of the new machines, tool materials and methods for gear treatment.
Izvestiya MGTU MAMI. 2012;6(2-2):248-252
248-252
Identification of the most significant areas of parameters estimation in development of the criterial approach for the selection of measurements means in designing and modernization of technological processes
摘要
The article considers the preconditions for development of the criterial approach system for the choice of measurements means in designing and modernization of technological processes. Also, main spheres of measurement means parameters are chosen and explained.
Izvestiya MGTU MAMI. 2012;6(2-2):253-257
253-257
Analysis of measuring errors and an object in determining residual stresses
摘要
The article is devoted to the identification of errors meter and an object in determining residual stresses in parts of gas turbine engines. Moreover, analysis of influence of the state of the surface of the measured residual stresses is made.
Izvestiya MGTU MAMI. 2012;6(2-2):257-265
257-265
Method of chemical reactions rate detection in the processes of neutralization of exhaust gases
摘要
The paper provides some general information and calculations of the chemical reactions of catalytic neutralization rate of exhaust gases, from which we can conclude that the temperature is the main parameter of exhaust gases process neutralization.
Izvestiya MGTU MAMI. 2012;6(2-2):266-270
266-270
Possibility for finding of a common solution for Navier-Stokes equations
摘要
The paper considers equations of a particle of a Newtonian fluid motion (equations of Navier-Stokes) in a vector form. The equality to zero of a rotor of the gradient is used, so it allows to move to one vector equation only by the speed and rotor speed. This equation contains the linear and quadratic terms. On the basis of the observations of the trajectories of the liquids flow in leakage from the tank through a tube, the trajectories of the flow does not change when fluid consumption changes, the conclusion is that with a change in flow velocity the equality of quadratic and linear parts of the motion equations can only be stored in that case, if these parts are equal to zero. This allows you to move to a more simple system of equations than the Navier-Stokes equations.
Izvestiya MGTU MAMI. 2012;6(2-2):270-277
270-277
Radiospectroscopy of magnetic materials
摘要
The paper presents the results of experimental and theoretical research of magnetic materials synthesized for use in the creation of functional radio electronics devices. Observations showed paramagnetic resonance, ferromagnetic resonance, resonance of the magnetostatic spin waves, nonresonant absorption of electromagnetic waves during the quasistatic magnetization reversal of the objects of research. According to the results of measurings of the observed physical phenomena were calculated studied magnetic materials characteristics; magnetization, anisotropy constants and so on.
Izvestiya MGTU MAMI. 2012;6(2-2):277-285
277-285
Observability in problems of mathematical physics
摘要
Attention is drawn to the importance of the observation principle in the physical Sciences, which means that hypothesis and theory should be formulated in terms of observable nature values. Experiment and practice, not the opinions of authorities, are criteria of truth. Forgetting this leads to big, but ineffectual material expenses.
Izvestiya MGTU MAMI. 2012;6(2-2):285-289
285-289
Approximate model of forecasting resource during the impact of non-Gaussian processes
摘要
The article develops approximate forecasting model assessments of fatigue life of power elements for the case of loading of stationary stochastic processes with the law of distribution ordinate different from the law of Gauss. The proposed predictive model is a correction of the Gaussian narrow-band model and can be used to obtain an express-assessment of the resource at the stage of elaborating the draft project of the loading of non-Gaussian processes.
Izvestiya MGTU MAMI. 2012;6(2-2):289-293
289-293
Numerical solution for the stress concentration problem for the case of a three-layered elastic plane with the two identical vertically placed circular holes under transverse compression
摘要
The results on the stress distribution in a transversally compressed three-layered elastic plane with the two identical vertically placed circular holes, received by using a variational finite-difference procedure for solving plane elastic problems for the holed rectangular domains, are presented. The effects of the layers' elastic constants on the level of stresses around the holes are examined.
Izvestiya MGTU MAMI. 2012;6(2-2):294-298
294-298
Analysis and synthesis of robust control for linear systems of double damping
摘要
The paper sets forth the method for constructing a robust control suspension of the automobile when there is an interval uncertainty of car cargo weight and drivers’ mass as well as the impossibility of measuring deviations of the car body and the driver's seat of their state of rest. The paper gives clear justification for the relevance of the application of synthesized robust control in comparison with other on the quality of the transient processes.
Izvestiya MGTU MAMI. 2012;6(2-2):298-305
298-305
Dynamic robust stabilization problem for the linear nonstationary systems
摘要
The paper gives the definition of robust stabilization tasks of the object and the d-robust task; provides a definition of robust control and the method of synthesis of optimal guaranteed control is indicated, and the withdrawn selection rules of the indignation worst parameters from the known range; considers the formula that relates under some of the worst parameters the initial state of the object, restrictions on the right end and the time of the transition process system for which it should go to the state, satisfying the boundary restrictions. The theoretical results are supported by numerical examples.
Izvestiya MGTU MAMI. 2012;6(2-2):305-311
305-311
The conclusion of the Dirac matrices in the real, complex and quaternionic representations
摘要
The article examines the relationship between the laws of the multiplication of vectors in the covariant Clifford algebra and Dirac matrices. The result is that spatial Dirac matrices are recorded in the form of a matrix structural permanent Clifford algebra over a geometric space. Spatio-temporal Dirac matrices represent the structural constants of the condensed Clifford algebra on the space-time. The structural constants are considered on the set of real numbers, complex numbers and quaternions.
Izvestiya MGTU MAMI. 2012;6(2-2):311-318
311-318
Basic experiment and method for identifying of material functions of elastic-plastic deformation theory
摘要
This article considers basics and equations of the theory of elastic-plastic deformation. The material functions closing theory are particularly highlighted. The authors formulated the basic experiment and method of identification of material functions.
Izvestiya MGTU MAMI. 2012;6(2-2):318-323
318-323
The problem of spreading of the plastic layer consisting of different environments
摘要
The paper presents application of the theory of flow of the plastic layer between approaching surfaces of the tool body, modeling the processes of forming and molding of thin-walled structural elements. Within the simplified statement a boundary-value problem of the flow of a thin plastic layer shaped region composed of two different environments is formulated. The authors provide the precise solution of the problem with respect to the flow velocity and contact pressure. They derived the evolution equation for determining of the boundaries of spreading plastic layer. It is shown that the boundary wedge areas remain straight.
Izvestiya MGTU MAMI. 2012;6(2-2):323-330
323-330
Multicriteria optimal design turbomachine disk
摘要
Modern concepts of using optimization technologies for structural design are considered. Several approaches of optimization problems for compressor disk are considered. The problem of total weight minimization under certain stress and stiffness constraints is investigated. All results were obtained using developed FE analysis program connected with SQP optimization procedure.
Izvestiya MGTU MAMI. 2012;6(2-2):330-336
330-336
Generalized method of supplementary strain in the problems of beam torsion
摘要
Generalized supplementary strain method efficiency is shown by beam elastoplastic torsion problem solving using BEM formulation. Dependence of convergence rate on modified shear modulus and on the twist angle was studied. Optimal choice of plasticity parameter leads to maximum convergence rate for this method.
Izvestiya MGTU MAMI. 2012;6(2-2):336-341
336-341
Approximation of plasticity functionals of elastic-plastic processes theory in non-isothermal loading under creep conditions
摘要
Based on the equations of inelasticity related to the class of flow theories in the combined hardening authors obtained the applied version of the theory of elastic-plastic processes and approximation of plasticity functionals in non-isothermal loading in creep conditions.
Izvestiya MGTU MAMI. 2012;6(2-2):341-345
341-345