Influence of the mode parameters on the technological characteristics of the injector hole broaching operation
- Authors: Belov I.I.1, Gruzdev A.A.1, Saushkin B.P.1
-
Affiliations:
- Moscow State University of Mechanical Engineering (MAMI)
- Issue: Vol 6, No 2-2 (2012)
- Pages: 77-83
- Section: Articles
- URL: https://journals.rcsi.science/2074-0530/article/view/68428
- DOI: https://doi.org/10.17816/2074-0530-68428
- ID: 68428
Cite item
Full Text
Abstract
Influence of the pulse duration on the machining time and instrument wear touching the electroerrosion drilling of the little diameter holes on the special machine tool is shown experimentally in this paper. The dependence between speed of erosion and hole depth is investigated. The statistical regularity of distribution operation time and the instrument wear speed is revealed. Engineering solutions for a higher stability drilling of the holes are proposed.
Full Text
##article.viewOnOriginalSite##About the authors
I. I. Belov
Moscow State University of Mechanical Engineering (MAMI)
Email: dron_1111@mail.ru
A. A. Gruzdev
Moscow State University of Mechanical Engineering (MAMI)
B. P. Saushkin
Moscow State University of Mechanical Engineering (MAMI)Dr. Eng., Prof.
References
- Современные технологии в производстве газотурбинных двигателей. / А.Г. Братухин, Г.К. Язов, Б.Е. Карасев, Ю.С. Елисеев, В.В. Крымов, И.П. Нежурин – М.: Машиностроение. 1997.
- Электроэрозионная обработка отверстий малого диаметра. / Ю.С. Елисеев, А.Н. Трошин / Журнал Авиационная промышленность № 1. 2001.
- Физико-химические методы обработки в производстве газотурбинных двигателей. / Ю.С. Елисеев, Б.П. Саушкин; под ред. Б.П. Саушкина.– М.: Изд-во МГТУ им. Н.Э.Баумана. 2010.
- Справочник по электроэрозионной обработке материалов. / Е.Ф. Немилов – Л.: Машиностроение. 1989.
- Бенников В.С., Моргунов Ю.А., Саушкин С.Б., Саушкин Г.Б. Статистический анализ точности операции электрохимической обработки пера лопаток компрессора. Журнал «Известия МГТУ «МАМИ», 2009, с.87-91
- Моргунов Ю.А., Саушкин С.Б. Структурное моделирование и классификация способов электрохимической размерной обработки. Журнал «Известия МГТУ «МАМИ», 2011, № 1, с. 184-188.
- Шандров Б.В. Прогрессивные технологии автомобилестроения/Журнал автомобильных инженеров, № 6. 2004.
- Максимов Ю.В., Абрамова А.Р., Кузьминский Д.Л., Мокринская А.Ю. К вопросу об обеспечении качества обработки сложнопрофильных деталей на станках с изменяющимися элементами. Известия МГТУ «МАМИ», № 1(13), 2012, с. 168-174.