Application of an axisymmetric rigid-plastic finite element membrane model for evaluation of friction coefficients in sheet metal forming processes
- Authors: Petrov V.K.1, Mikhaylova V.L.1, Sukhomlinov L.G1
-
Affiliations:
- Moscow State University of Mechanical Engineering (MAMI)
- Issue: Vol 6, No 2-2 (2012)
- Pages: 150-158
- Section: Articles
- URL: https://journals.rcsi.science/2074-0530/article/view/68485
- DOI: https://doi.org/10.17816/2074-0530-68485
- ID: 68485
Cite item
Full Text
Abstract
The results of computational and experimental investigations are presented on the application of an axisymmetric rigid-plastic finite element membrane model for evaluation of friction coefficients in sheet metal forming processes. The data on hemispherical punch stretching of a sheet metal under investigation are used. The method's possibilities are demonstrated by examining cases with different friction conditions.
Full Text
##article.viewOnOriginalSite##About the authors
V. K. Petrov
Moscow State University of Mechanical Engineering (MAMI)Ph.D.
V. L. Mikhaylova
Moscow State University of Mechanical Engineering (MAMI)Ph.D.
L. G Sukhomlinov
Moscow State University of Mechanical Engineering (MAMI)Dr.Eng., Prof.
References
- Pearce R. Some effects of friction in punch-stretching// Dev. Draw. Metals. Proc. Int. Conf. / London. 11-13 May. 1983. / London. 1983. P. 249-254.
- Одинг С.С., Максименков В.И. Определение коэффициента трения при формировании осесимметричной оболочки. // Известия вузов. Машиностроение. 1984. № 8. с. 23-27.
- Ведмедь Ю.П., Юдович С.З., Фишман И.М. Определение коэффициента трения между пуансоном и заготовкой при листовой штамповке. // Кузнечно-штамповочное производство. 1972. № 4. с. 25-26.
- Fratini L., Lo Casto S., Lo Valvo E. A technical note on an experimental device to measure friction coefficient in sheet metal forming. // Journal of Materials Processing Technology. 2006. V. 172. № 1. P. 16-21.
- Wang N.-M., Budiansky R. Analysis of sheet metal stamping by a finite-element method. // Trans. ASME. J. Appl. Mech. 1978. V. 45. № 1. P. 73-82.
- Матвеев А.Д., Сухомлинов Л.Г., Жиляев С.Д., Соловей Е.М. Расчетно-экспериментальная методика определения коэффициента трения для предельного формоизменения при листовой формовке. // Вопросы исследования прочности деталей машин. Сборник научных трудов кафедры «Прикладная механика» МИП. М. 1994. с. 104-107.
- Сухомлинов Л.Г., Энгельсберг В.К. Конечноэлементная система автоматизированного расчета напряженно-деформированного состояния тонких оболочек в процессах осесимметричного формоизменения под действием жестких штампов. // Известия вузов. Машиностроение. 1989. № 3. с. 66-71.
- Sukhomlinov L.G., Engelsberg V.K., Davydov V.N. A finite element membrane model for the analysis of axisymmetric sheet metal forming processes. // Int. J. Mech. Sci. 1992. V. 34. № 3. P. 179-193.