检索

标题
作者
Selection of the analytical dependency for assessment of slipping of the Kirovets K-7 wheeled agricultural tractor
Anisimov N., Efimov E., Dobretsov R., Dmitriev M.
Bench assembly for diesel engine tests with water injection in an inlet collector
Dmitriev S., Khlyupin V.
Endurance testing of tractor friction clutches
Mikhaylov V., Sharipova N., Esenovsky-Lozhkov M.
Experimental study of plastics hardness
Frolov V., Shcherbakov Y., Skachkov Y.
Experimental evaluation of the load capacity of the rollers of gravity conveyors for pallets
Safronov Y., Nosko A.
The study of motion of the snow and swamp-going vehicle with the traction electric drive, based on the Emrax 228 electric motor
Sarach M., Sarach E., Kaplan D.
Study of damping properties, thermal and strength characteristics of anaerobic materials
Toulinov A., Goncharov A.
Simulation of mechanical tests aimed to investigate the flow stress during the abrupt change of the strain rate
Potapenko K., Voronkov V., Petrov P.
Determination of fuel consumption of light commercial truck on a given route
Kravets V., Musarsky R., Moshkov P., Toropov E.
Optimization of the ethanol-fuel emulsion composition for use in diesel engines
Plotnikov S., Kartashevich A., Plyago A., Pachurin G.
The low power diesel-generator unit with electronically controlled fuel injection
Galiullin R., Potapov V.
The Role of Certification Test Grounds to Ensure the Quality of Created and Upgraded Road and Track Vehicles
Gribanov D., Fedulov A.
Influence of geometry and design of a roller-type dynamometer on the accuracy of cornering characteristics of automobile tires
Kondrashov V., Bernadskiy V.
Method for increasing the reliability of transmission bench testing
Lyashenko M., Shekhovtsov V., Sokolov-Dobrev N.
Development of a complex of mathematical models of a vehicle suspension for fatigue life analysis
Kulagin V.
The role of information-measuring systems in improving of wheeled and tracked vehicles testing process
Larionova O.
Principles of selection of cutting technological mediums for metal cutting
Kuscheva M., Klauch D., Kobelev O.
Tribological tests of solid lubricating coatings at elevated temperatures and loads
Sutyagin O., Bolotov A., Rachishkin A.
Validation of the CAE model set for a passenger car suspension according to loading criteria
Kulagin V.
Development of a mathematical model of an energy-absorbing seat, using the results of piling tests
Kulakov N., Gavrilov E.
Full-scale-model tests of materials and coatings at simulation of intense radiation and convective heat transfer of heat power equipment elements
Merzlikin V., Maximov A., Tovstonog V., Krokhalev I.
Multi-functional test bench
Gorobtsov A., Lyashenko M., Sokolov-Dobrev N., Shekhovtsov V., Potapov P., Klementyev E., Dolotov A.
Modern approach to testing and validation of driver assistance systems
Toropov Y., Trusov Y., Vashurin A., Moshkov P.
Development of test-benches for control and research tests of turbochargers
Kaminskiy V., Kaminskiy R., Lazarev A., Grigorov I., Kostyukov A., Korneev S., Kovaltsov I., Sergeev A., Gusak A., Sibiryakov S.
Tribological characteristics of dispersed-filled composite materials
Pechnikov A., Toleshuli A., Meshcheryakov E.
Mathematical model of test bench
Gorobtsov A., Lyashenko M., Sokolov-Dobrev N., Shekhovtsov V., Potapov P., Klementyev E., Dolotov A.
Topological optimization of the load-bearing structure of the safety cage
Zhitelev D., Pozdnyakov T., Sulegin D.
Accuracy Enhancement for Vehicle Motion Mathematical Model on the Basis of Test Results
Kurmaev R., Lepeshkin A.
Numerical and experimental investigation of braking performance of a bus
Groshev A., Konikova G., Kostin S., Trusov Y., Tumasov A.
Stabilization of gas temperature and rotor speed on test-bench for control and research testing of turbochargers by means of automation
Kovaltsov I., Kaminskiy R., Kaminskiy V., Sibiryakov S., Korneev S., Zaitsev O.
The method of simulating the loading of boosted diesel engine during start-up at low ambient temperatures
Bondar V., Kukis V., Malozyomov A.
Definition of parameters of loading modes of the test bench for tractor cabin’s vibration isolators
Gozhaev Z., Shekhovtsov V., Potapov P., Iskaliev A., Yarkina M., Evseeva A.
PERFECT AND IMPERFECT NONHOLONOMIC KINEMATIC CONNECTIONS OF THE ROAD WHEEL WITH SURFACE
Katanaev N.
Application of laser welding technology in manufacture of pressure vessels of titanium alloy
Kochergin S., Saushkin B.
Natural-model tests of materials and coatings in simulated intense radiant and convective heat transfer of elements of heat and power equipment. Part 2: Physical and technical characteristics of thermal stand for testing of materials and coatings of diesel engine thermally insulated combustion chamber
Merzlikin V., Maximov A., Tovstonog V., Chirin K., Abdulmyanov R.
Comparison of traction and longevity of caterpillar driving machines of agricultural tractors
Shchel'tsyn N., Beynenson V., Fedotkin R., Kryuchkov V., Belyy I., Revenko V.
1 - 36 的 36 信息

检索提示:

  • 检索的名词区分大小写
  • 常用字词将被忽略
  • 默认情况下只有在查询结果满足所有检索词才返回(例如,隐含AND)
  • 使用OR结合多个检索词,便于查找含有这些检索词的文章,例如education OR research
  • 使用括号来创建更复杂的查询; 例如:archive ((journal OR conference) NOT theses)
  • 使用引号检索一个完整的词组; 例如: "open access publishing"
  • 使用-或者NOT排除一个检索词; 例如:online -politics or online NOT politics
  • 在检索词里使用 *作为通配符匹配任何字符序列; 例如., soci* morality 将符合含有 "sociological" or "societal"的词语
##common.cookie##