Simulation of mechanical tests aimed to investigate the flow stress during the abrupt change of the strain rate
- Authors: Potapenko K.E1, Voronkov V.I.1, Petrov P.A1
-
Affiliations:
- Moscow State University of Mechanical Engineering (MAMI)
- Issue: Vol 7, No 2-2 (2013)
- Pages: 178-183
- Section: Articles
- URL: https://journals.rcsi.science/2074-0530/article/view/68183
- DOI: https://doi.org/10.17816/2074-0530-68183
- ID: 68183
Cite item
Full Text
Abstract
This article describes a modeling procedure of material’s mechanical test during the abrupt change of the strain rate. Simulation results were compared with the data obtained experimentally. The numerical simulation was performed in the FE-program QFORM. The paper describes the selection of areas for further research related to the definition of mathematical models of deformation resistance, and it also contains the software requirements for the simulation of mechanical tests.
Full Text
##article.viewOnOriginalSite##About the authors
K. E Potapenko
Moscow State University of Mechanical Engineering (MAMI)
Email: v-i-w@bk.ru
Ph.D.; 8(495)223-05-23, ext. 1306
V. I. Voronkov
Moscow State University of Mechanical Engineering (MAMI)
Email: v-i-w@bk.ru
8(495)223-05-23, ext. 1306
P. A Petrov
Moscow State University of Mechanical Engineering (MAMI)
Email: v-i-w@bk.ru
8(495)223-05-23, ext. 1306
References
- Гринберг И. В., Петров П. А., Гневашев Д. А., Воронков В. И., Физическое и математическое моделирование процесса изготовления тонкостенных оболочек в штампе для выдавливания: Технология легких сплавов: 2, 2010, стр. 101 – 106.
- Воронков В. И., Потапенко К. Е., Определение кривых текучести материалов с применением компьютерного моделирования. Материалы 77-й Международной научно-технической конференции ААИ «Автомобиле- и тракторостроение в России: приоритеты развития и подготовка кадров»: МГТУ «МАМИ» 2012, стр. 115 – 124.
- Petrov P., Voronkov V., Potapenko K., Ivanov V., The Effect of transient change in strain rate on plastic flow behaviour of Al-Mg-Si alloy at elevated temperatures, Proceedings of the 14th international conference on material forming ESAFORM, AIP Conference Proceedings, Vol. 1353, 2011, pp. 374 – 379.
- Petrov P., Voronkov V., Potapenko K., Petrov M., Research into flow stress of Al-Mg-Si alloy during the abrupt change of the strain rate at elevated temperatures: Computer Methods in Materials Science: Proceedings of the conference Komplastech: 2013, pp. 63 – 67.
- Petrov P., Voronkov V., Potapenko K., Petrov M., Gamzina O., Research into the flow stress of Al-Mg-Si alloy (AD-35) during the abrupt change of the strain rate at elevated temperatures, Key Engineering Materials, Proceedings of the international conference on material forming ESAFORM, Vols. 554 – 557, 2013, pp. 1099 – 1104
- Шпунькин Н.Ф., Типалин С.А. Исследование свойств многослойных листовых материалов / Заготовительные производства в машиностроении. 2013. №1. С.28-31.
- Типалин С.А. Определение накопленной деформации в процессе выдавливания технологической канавки / Заготовительные производства в машиностроении. 2013. №8. С.22-29.
- Крутина Е.В., Калпин Ю.Г. Определение пластичности металлов методом комбинированного поперечного выдавливания и высадки / Известия МГТУ «МАМИ». 2012. Т.2. №2. С.95-98.
- Соболев Я.А., Аверкиев А.Ю., Шпунькин Н.Ф., Феофанова А.Е. Ковка и штамповка / Справочник в 4 т. / Москва 2010.
- Типалин С.А., Шпунькин Н.Ф., Никитин М.Ю., Типалина А.В. Экспериментальное исследование механических свойств демпфирующего материала / Известия МГТУ «МАМИ» 2010. №1. С166-170.
- Потапенко К.Е., Пеньков И.В., Воронков В.И., Петров П.А., Шайхулов М.В. Исследование контактного трения при горячей пластической деформации сплава АВ / Заготовительные производства в машиностроении. 2012. №6. С.18-21.