OPTIMIZATION OF THE PARAMETERS OF THE PRIMARY TRANSDUCER OF THE DYNAMIC INSTRUMENTED INDENTATION DEVICE WITH A DIFFERENTIAL COIL

封面

如何引用文章

全文:

开放存取 开放存取
受限制的访问 ##reader.subscriptionAccessGranted##
受限制的访问 订阅存取

详细

The issues of improving the accuracy of estimating the indenter motion parameters in the primary converter of a dynamic instrumented indentation device using two counter-connected coil windings (differential coil) are considered. The calculation of the characteristics of the primary converter is based on computer modeling and solving the problem of step-by-step conditional optimization of the relative dimensions of the striker magnet and coil. The results of a study of a primary converter with a differential coil (comparative estimates of the recorded signal — EMF and the dynamic modulus of elasticity of steel St.3) in relation to the existing primary sensor converter of the TPTS-7 device, which showed its advantage.

作者简介

O. Kolganov

ITMO University

Email: кolganoff2014@yandex.ru
St. Petersburg, Russia

K. Doronin

St. Petersburg Mining University of Empress Catherine II

Email: doronin.k.i@mail.ru
St. Petersburg, Russia

A. Golev

LLC CONSTANT

Email: artemgolev1999@gmail.com
St. Petersburg, Russia

参考

  1. ГОСТ Р 56474—2015. Контроль неразрушающий физико-механических свойств материалов и покрытий космической техники методом динамического индентирования. М.: Стандартинформ, 2015. С. 15—17.
  2. Рудницкий В.А., Рабцевич А.В. Метод динамического индентирования для оценки механических характеристик металлических материалов // Дефектоскопия. 1997. № 4. С. 79—86.
  3. Егоров Р.А., Ильинский А.В., Кузьмичев М.В., Федоров А.В. Аппаратно-алгоритмическое обеспечение процесса динамического индентирования // Дефектоскопия. 2020. № 6. С. 61—69.
  4. ГОСТ 8.969—2019 (ИСО 16859-1:2015) Государственная система обеспечения единства измерений (ГСИ). Металлы и сплавы. Определение твердости по шкалам Либа. Часть 1. Метод измерений.
  5. Khoshev A., Kolganov O., Egorov R.A., Fedorov A.V., Kinzhagulov I.U. Computer Simulation of Registration of Indenter Motion in the Process of Contact-Impact Interaction / 2023 7th International Conference on Information, Control, and Communication Technologies (ICCT). 2023. P. 1—4.
  6. Колганов О.А., Егоров Р.А., Ильинский А.В., Хошев А.Е., Федоров А.В. Дифференциальное включение катушек индуктивности для регистрации параметров движения ударника при динамическом индентировании // Известия высших учебных заведений. Приборостроение. 2023. Т. 66. № 1. С. 74—80.
  7. Твердомеры портативные цифровые ТПЦ // GRmetr.ru URL: https://grmetr.ru/gosreestr/1409012-89241-23-tpts (дата обращения: 26.05.2024).
  8. ГОСТ 1497—84 (ИСО 6892-84) Методы испытаний на растяжение: дата введения 01.01.1986. М.: Стандартинформ, 2008. 26 с.
  9. GOST R 56474—2015. Non-destructive control of physical and mechanical properties of materials and coatings of space technology by dynamic indentation. M.: Standartinform, 2015. P. 15—17.
  10. Rudnitsky V.A., Rabtsevich A.V. The method of dynamic indentation for evaluating the mechanical characteristics of metallic materials // Defectoskopiya. 1997. No. 4. P. 79—86.
  11. Egorov R.A., Ilyinsky A.V., Kuzmichev M.V., Fedorov A.V. Hardware and algorithmic support of the dynamic indentation process // Defectoskopiya. 2020. No. 6. P. 61—69.
  12. GOST 8.969—2019 (ISO 16859-1:2015) State system for ensuring the uniformity of measurements (GSI). Metals and alloys. Determination of hardness according to Lieb scales. Part 1. Measurement method.
  13. Khoshev A., Kolganov O., Egorov R.A., Fedorov A.V., Kinzhagulov I.U. Computer Simulation of Registration of Indenter Motion in the Process of Contact-Impact Interaction / 2023 7th International Conference on Information, Control, and Communication Technologies (ICCT). 2023. P. 1—4.
  14. Kolganov O.A., Egorov R.A., Ilyinsky A.V., Khoshev A.E., Fedorov A.V. Differential inclusion of inductors for recording the parameters of the striker’s motion during dynamic indentation // Izvestiya vysshchih uchebnykh zavedeniy. Instrumentation. 2023. V. 66. No. 1. P. 74—80.
  15. Portable digital TPC hardness testers // GRmetr.ru URL: https://grmetr.ru/gosreestr/1409012-89241-23-tpts (date of reference: 05/26/2024).
  16. GOST 1497—84 (ISO 6892-84) Tensile testing methods: date of introduction 01.01.1986. M.: Standartinform, 2008. 26 p.

版权所有 © Russian Academy of Sciences, 2024

##common.cookie##