Inspection of press joints based on the analysis of their deformation patterns under local thermal loading

Мұқаба

Дәйексөз келтіру

Толық мәтін

Ашық рұқсат Ашық рұқсат
Рұқсат жабық Рұқсат берілді
Рұқсат жабық Тек жазылушылар үшін

Аннотация

The results of experimental studies of the possibility of using strain gauges under local pulsed thermal loading to evaluate the tension of the press connections of bearing rings with shafts are presented. Samples of press joints with tightness in the range from 38 to 118 microns were made. As a result of the study of the patterns of heat flow propagation in bearing rings and tension samples by contact method and means of thermal imaging, the possibility of separating deformations associated with the influence of temperature on the deformation measurement area and the temperature gradient in the heating area is shown. The methods of inspecting the press joint when exposed to a heater ring with a heat power capacity of 80 kJ and a temperature of 200°C and measuring the deformations of the ring and shaft by an opto-polarizing sensor with a base of 60 mm and a resolution of 2×10 — 7 relative deformations have been experimentally implemented. A correlation has been established between the time of reaching the maximum of local deformations of the shaft with the tightness of the press joints and the sign of deformations of the bearing ring with the tightness of the press fit, the gap between the ring and the shaft.

Толық мәтін

Рұқсат жабық

Авторлар туралы

S. Becher

Siberian transport university

Email: fedorinin55@mail.ru
Ресей, 630049, Novosibirsk, str. Dusi Kovalchuk, 191

A. Popkov

Siberian transport university

Email: fedorinin55@mail.ru
Ресей, 630049, Novosibirsk, str. Dusi Kovalchuk, 191

A. Vyplaven

Siberian transport university

Email: fedorinin55@mail.ru
Ресей, 630049, Novosibirsk, str. Dusi Kovalchuk, 191

V. Fedorinin

Branch of IFP SB RAS “Design and Technological Institute of Applied Microelectronics”

Хат алмасуға жауапты Автор.
Email: fedorinin55@mail.ru
Ресей, 630090, Novosibirsk, ak. Lavrentieva ave., 2/1

V. Sidorov

Branch of IFP SB RAS “Design and Technological Institute of Applied Microelectronics”

Email: fedorinin55@mail.ru
Ресей, 630090, Novosibirsk, ak. Lavrentieva ave., 2/1

S. Shlyakhtenkov

Siberian transport university

Email: shlyakhtenkow@gmail.com
Ресей, 630049, Novosibirsk, str. Dusi Kovalchuk, 191

I. Kinzhagulov

ITMO National Research University

Email: fedorinin55@mail.ru
Ресей, 197101, St. Petersburg, Kronverksky Prospekt, 49, litera A

Әдебиет тізімі

  1. Carpenter Chris. Fatigue Testing of Shrink-Fit Couplings for Joining High-Strength-Steel Riser Pipe // Journal of Petroleum Technology. 2015. V. 65. P. 108—111.
  2. Bezyazychnyj V.F., Fedulov V.M. The methodology of technological support of operational indicators in the assembly of joints with tension // Sborka v mashinostroenii, priborostroenii. 2020. № 6. P. 270—276.
  3. Hehe Kang, Zhi-Min Li, Tao Liu, Guang Zhao, Jianping Jing, Wei Yuan. A novel multiscale model for contact behavior analysis of rough surfaces with the statistical approach // International Journal of Mechanical Sciences. 2021. V. 212.
  4. Lior Kogu, Izhak Etsion. A Finite Element Based Elastic-Plastic Model for the Contact of Rough Surfaces // Tribology Transactions. 2003. V. 46. No. 3. P. 383—39.
  5. Kuliev S.A., Mamedov A.F. Determination of stresses in the connection hub with tension during loading // Vestnik mashinostroeniya. 2019. No. 7. P. 27—30.
  6. Rozhkova E.A., Chetverikov S.V. The method of conducting experimental studies of the stress-strain state of profile joints with tension // Vestnik Rossijskogo universiteta druzhby` narodov. Seriya: Inzhenerny`e issledovaniya. 2018. V. 19. No. 1. P. 46—58.
  7. Mamedov A.F. Calculation of the connection with tension to the shock load // Problemy` mashinostroeniya i avtomatizacii. 2019. No. 4. P. 85—87.
  8. Matlin M.M., Kazankin V.A., Kazankina E.N. Methods for improving the effectiveness of tightening control of threaded connections // Ximicheskoe i neftegazovoe mashinostroenie. 2020. № 7. P. 40—42.
  9. Boutoutaou H., Bouaziz M., Fontaine J.F. Modeling of interference fits taking form defects of the surfaces in contact into account // Materials & Design. 2011. V. 32. No. 7. P. 3692—3701.
  10. Wang X., Lou Z., Wang X., Wang Y., Hao X., Wang Z. Automatic press-fit assembly of small precision interference fitting parts: armature of electro-hydraulic servo valve // Assembly Automation. 2019. V. 39. No. 5. P. 986—998.
  11. Kupriyanov O., Trishch, R., Dichev D., Hrinchenko H. Experimental Studies on the Form Error Effect of the Part Mounting Surface on the Strength Quality Parameter of the Interference Fit Joints // Advanced Manufacturing Processes V. 2023. V. 10.
  12. Bedlaoui Allal, Boutoutaou Hamid. Effect of interference and form defect on the cohesion of the shrink-fit assembly // The International Journal of Advanced Manufacturing Technology. 2023. V. 128.
  13. Buketkin B.V., Semenov-Ezhov I.E., Shirshov A.A. Stress relaxation in bolted joints with radial tension // Inzhenerny`j zhurnal: nauka i innovacii. 2019. № 10 (94). P. 1.
  14. Arslan M.A. Coupled thermal/structural contact analyses of shrink-fit tool holder // Journal of Engineering Manufacture. 2014. V. 228 (5). P. 715—724.
  15. Wang X., Lou Z., Wang X., Hao X., Wang Y. Prediction of stress distribution in press-fit process of interference fit with a new theoretical model // Journal of Mechanical Engineering Science. 2019. V. 233(8). P. 2834—2846.
  16. Saeedi R., Sadeghi M. Investigation of insert-hole interference fit influence on downhole drilling bit failure // Journal of Engineering Manufacture. 2020. V. 234 (14). P. 1752—1761.
  17. Santus C. Initial orientation of the fretting fatigue cracks in shrink-fit connection specimens // Frattura ed Integrità Strutturale. 2019. V. 13 (48). P. 442—450.
  18. Saeed Muhammad, Falter Jan, Dausch Valesko, Wagner Markus, Kreimeyer Matthias, Eisenbart Boris. Artificial intelligence techniques for improving cylindrical shrink-fit shaft-hub couplings // Proceedings of the Design Society. 2023. V. 3. P. 645—656.
  19. Zhou D., Lan S., Gao X. et al. Nondestructive Surface Threshold Definition for Remanufacturing Disassembly of Interference Fit // Int. J. Precis. Eng. Manuf. 2018. V. 19. P. 1735—1743.
  20. Bo You, Zhifeng Lou, Yi Luo, Yang Xu, Xiaodong Wang. Prediction of Pressing Quality for Press-Fit Assembly Based on Press-Fit Curve and Maximum Press-Mounting Force // International Journal of Aerospace Engineering. 2015. V. 2015. P. 10.
  21. Matlin M.M., Kazankina E.N., Kazankin V.A., Mozgunova A.I. Device for determining pressure in connection with tension / // Izvestiya Volgogradskogo gosudarstvennogo texnicheskogo universiteta. 2018. No. 9 (219). P. 80—83.
  22. Yang Liu, Mingxuan Li, Xiaofeng Lu, Qingsheng Li, Xiaolei Zhu. Pull-out performance and optimization of a novel Interference-fit rivet for composite joints // Composite Structures. 2021. V. 269.
  23. Wang Xingyuan, Liu Jiaxing, Lu Shujie, Wang Yue, Wang Xiaodong, Lou Zhifeng, Zhang Lixun. Connection force measurement of precision small interference components using ultrasound // Journal of Mechanical Engineering Science. 2023.
  24. Muraveva O.V., Volkova L.V., Muravev V.V. Sensitivity of the electromagnetic-acoustic multiple shadow method using Rayleigh waves in the control of oil grade pipes // Defektoskopiya. 2020. No. 12. P. 48—57.
  25. Muravev V.V., Volkova L.V., Platunov A.V., Buldakova I.V., Gushhina L.V. Studies of the structural and stress-strain state of rails of current production by the method of acoustoelasticity // Vestnik IzhGTU imeni M.T. Kalashnikova. 2018. V. 21. No. 2. P. 13—23.
  26. Bekher S.A., Stepanova L.N., Ry`zhova A.O., Bobrov A.L. Control of bearing ring tension by surface waves using the acoustoelasticity effect // Defektoskopiya. 2021. No. 4. P. 13—21.
  27. Buinosov A.P., Vetlugina O.I., Guzenkova E.A. Development of an ultrasonic method for monitoring the tension of the bandage on the rim of the wheel center with the bandages attached // Nauka i obrazovanie transportu. 2022. No. 1. P. 13—15.
  28. Buldakova I.V., Volkova L.V., Muravev V.V. Stress distribution in pipe samples of main gas pipelines with welded connection // Intellektualnye sistemy v proizvodstve. 2020. V. 18. № 1. P. 4—8.
  29. Król Roman, Siemiątkowski Zbigniew. The analysis of shrink-fit connection – the methods of heating and the factors influencing the distribution of residual stresses // Heliyon. 2019. V. 5, No. 11.
  30. Wu X., Li C., Sun S., Tong R., Li Q. A Study on the Heating Method and Implementation of a Shrink-Fit Tool Holder // Energies. 2019. No. 12.
  31. Fedorinin V.N., Sidorov V.I. Polarizing optical sensors for measuring physical quantities // Zhurnal analiticheskoi khimii. 2005. V. 55. No. 7.
  32. Fedorinin V.N., Bekher S.A., Vyplaven V.S. Optical strain gauge in the problem of wheel-rail interaction // Avtometriia. 2023. V. 59. No. 3. P. 33—42.

Қосымша файлдар

Қосымша файлдар
Әрекет
1. JATS XML
Жүктеу
2. Fig. 1. Problem statement.

Жүктеу (477KB)
Метадеректер
3. Fig. 2. Sketch of the samples of the joints of the ring with the axis with tension n after (a) and before (b) the press fit.

Жүктеу (305KB)
Метадеректер
4. Fig.3. Test scheme: a sample of a press joint with a deformation sensor, a thermistor and a heating bar (a); temperature and deformation measurement sites (b).

Жүктеу (1016KB)
Метадеректер
5. Fig. 4. Temperature dependence on time during tests at a distance from the heated bar 35 mm (a) and 124 mm (b) next to the deformation sensor.

Жүктеу (414KB)
Метадеректер
6. Fig. 5. Thermograms of the ring surface after 20 s (a) and 80 s (b) after the start of heating and temperature profiles on a semi-logarithmic scale (c).

Жүктеу (543KB)
Метадеректер
7. Fig. 6. Time dependences of deformations of the bearing ring, measured by the sensor pos. 2 Fig. 3b, when testing a free ring, a sample without tension and a sample with tension.

Жүктеу (240KB)
Метадеректер
8. Fig. 7. The results of finite element modeling of the free ring of the bearing and the pressure joint with tension: the dependence of deformations (a) and temperature (b) on time, the shape of the free ring and the temperature field 2 s (c) and 98 s (d) after the start of heating.

Жүктеу (791KB)
Метадеректер
9. Fig. 8. Time dependences of deformations (a) of the shafts of press joints with different strains, measured by the sensor pos. 2 Fig. 3b, and the rates of change of deformations averaged over the interval of 2 s (b) and 50 s (c).

Жүктеу (598KB)
Метадеректер

© Russian Academy of Sciences, 2024

Осы сайт cookie-файлдарды пайдаланады

Біздің сайтты пайдалануды жалғастыра отырып, сіз сайттың дұрыс жұмыс істеуін қамтамасыз ететін cookie файлдарын өңдеуге келісім бересіз.< / br>< / br>cookie файлдары туралы< / a>