| 期 |
标题 |
文件 |
| 卷 60, 编号 5 (2019) |
Study of Compaction of the Titanium Powder by the Experimental-Analytical Method |
(Eng)
|
|
Zalazinskii A., Nesterenko A., Berezin I.
|
| 卷 60, 编号 3 (2019) |
Methods of Compaction of the Al–B–W Powder Composition in a Metal Shell |
(Eng)
|
|
Glushenkov V., Belyaeva I., Grechnikov F., Mironov V., Usherenko Y., Pesotsky V.
|
| 卷 60, 编号 2 (2019) |
Analysis of the Scheme of Nonequal Channel Angular Pressing as Applied to the Formation of Sheet Magnesium in a Cold State |
(Eng)
|
|
Loginov Y., Volkov A., Kamenetskiy B.
|
| 卷 60, 编号 2 (2019) |
Manufacturing Process and Interface Properties of Vacuum Rolling Large-Area Titanium-Steel Cladding Plate |
(Eng)
|
|
Chang-gen Shi ., Yang X., Shi H., Fang Z., Sun Z., Feng K., Shao F.
|
| 卷 60, 编号 1 (2019) |
Computer Simulation of Mannesmann Piercing of Aluminium Alloy Ingots |
(Eng)
|
|
Gladkov Y., Skripalenko M., Romantsev B., Bazhenov V., Tran B., Skripalenko M., Galkin S., Savonkin M.
|
| 卷 60, 编号 1 (2019) |
Investigation into the Influence of the Degree of Grinding of the Ingot Grain Structure of the 6063 Alloy on Its Plasticity, Extruding Parameters, and Properties of Extruded Profiles |
(Eng)
|
|
Syryamkin R., Gorbunov Y., Sidelnikov S., Otmahova A.
|
| 卷 59, 编号 6 (2018) |
Simulation of the Final Stage of the Direct Extrusion Method of Large-Size Rods at Small Elongations |
(Eng)
|
|
Kargin V., Deryabin A.
|
| 卷 59, 编号 4 (2018) |
Regularities of Formation and Degradation of the Microstructure and Properties of New Ultrafine-Grained Low-Modulus Ti–Nb–Mo–Zr Alloys |
(Eng)
|
|
Kolobov Y., Golosova O., Manokhin S.
|
| 卷 59, 编号 1 (2018) |
Investigation into the Formation of Texture, Microstructure, and Anisotropy of Properties during Rolling Sheets of the Aluminum–Lithium 1420 Alloy |
(Eng)
|
|
Grechnikov F., Erisov Y., Surudin S., Oglodkov M.
|
| 卷 59, 编号 1 (2018) |
Development of Fabrication Modes of Deformed Semifinished Products from the Experimental Scandium-Containing Aluminum Alloy and Investigation into Their Mechanical Properties |
(Eng)
|
|
Baranov V., Sidelnikov S., Zenkin E., Voroshilov D.
|
| 卷 59, 编号 1 (2018) |
Combined Effect of Calcium and Silicon on the Phase Composition and Structure of Al–10%Mg Alloy |
(Eng)
|
|
Belov N., Naumova E., Doroshenko V., Avxentieva N.
|
| 卷 58, 编号 6 (2017) |
A Study of Plastic Deformation Behavior of AA1050 Aluminum Alloy during Pure Shear Extrusion with Back Pressure |
(Eng)
|
|
Irani M., Joun M.
|
| 卷 58, 编号 5 (2017) |
Calculation of parameters of drawing-out the half-sphere parts in the stamp with an elastic element |
(Eng)
|
|
Nesterenko E., Grechnikov F.
|
| 卷 58, 编号 4 (2017) |
Pressing prismatic and screw profiles from copper M4 |
(Eng)
|
|
Ivanov A.
|
| 卷 58, 编号 3 (2017) |
Computational methods of the superplastic forming duration of a round membrane |
(Eng)
|
|
Kruglov A., Ganieva V., Tulupova O., Enikeev F.
|
| 卷 58, 编号 2 (2017) |
Possibilities of a new cold upsetting method for increasing magnesium plastification |
(Eng)
|
|
Kamenetskii B., Loginov Y., Kruglikov N.
|
| 卷 58, 编号 1 (2017) |
Application of combined casting–pressing for the fabrication of aluminum wire for soldering waveguides |
(Eng)
|
|
Gorokhov Y., Belyaev S., Uskov I., Konstantinov I., Gubanov I., Gorokhova T., Hramtsov P.
|
| 卷 57, 编号 6 (2016) |
Mathematical modeling of drawing rods made of titanium sponge allowing for pore formation |
(Eng)
|
|
Berezin I., Polyakov A.
|
| 卷 57, 编号 6 (2016) |
Finite element simulation of shot peening of an aluminum alloy considering hardening models |
(Eng)
|
|
Ahmadi M., Sadeghi B., Irani M., Rahimi F.
|
| 卷 57, 编号 5 (2016) |
Temperature modes and critical velocities when drawing the wire |
(Eng)
|
|
Kolmogorov G., Kosheleva N.
|
| 卷 57, 编号 3 (2016) |
Optimization of isothermal pressing of ingots of aluminum alloys with the preliminary gradient heating |
(Eng)
|
|
Pleshivtseva Y., Afinogentov A.
|
| 卷 57, 编号 3 (2016) |
Force conditions of pressing light-alloy drill pipes with spiral ribbing |
(Eng)
|
|
Afanas’ev A., Kargin V., Kargin B.
|
| 卷 57, 编号 2 (2016) |
Computer analysis of the deformation mode of the drawing tool for platinum alloys |
(Eng)
|
|
Ogorodnikova O., Borodin E.
|
| 卷 57, 编号 2 (2016) |
Computational-and-experimental evaluation of the implementation condition of combined rolling–pressing using the power balance method |
(Eng)
|
|
Zagirov N., Dovzhenko N., Sidel’nikov S., Bespalov V.
|
| 卷 57, 编号 2 (2016) |
Manufacturing residual stresses during the production of zirconium sheets |
(Eng)
|
|
Kuznetsova E., Kolmogorov G., Vavel’ A.
|
| 1 - 25 的 27 信息 |
1 2 > >>
|
