Investigation of the effect of modifying additives on the properties of copper obtained by casting

Capa

Citar

Texto integral

Acesso aberto Acesso aberto
Acesso é fechado Acesso está concedido
Acesso é fechado Somente assinantes

Resumo

The effect of additives containing chromium, zirconium, silicocalcium and carbon nanotubes on the physical-mechanical properties of copper obtained by casting is investigated. The tensile strength increased to 10.5%, Young’s modulus increased by 11.6–106.2%. The heat resistance of samples using SiCa increased by 1.9 times, Cu–Zr – by 1.5 times, with the use of nanotubes decreased by 1.2–1.8 times.

Sobre autores

B. Tolochko

Institute of Solid-State Chemistry and Mechanochemistry of the Siberian Branch of the Russian Academy of Science

Email: a-zhdanok@mail.ru
Russia, 630128, Novosibirsk

A. Zhdanok

Institute of Solid-State Chemistry and Mechanochemistry of the Siberian Branch of the Russian Academy of Science

Autor responsável pela correspondência
Email: a-zhdanok@mail.ru
Russia, 630128, Novosibirsk

V. Kuznetsov

Institute of Solid-State Chemistry and Mechanochemistry of the Siberian Branch of the Russian Academy of Science

Email: a-zhdanok@mail.ru
Russia, 630128, Novosibirsk

Z. Korotaeva

Institute of Solid-State Chemistry and Mechanochemistry of the Siberian Branch of the Russian Academy of Science

Email: a-zhdanok@mail.ru
Russia, 630128, Novosibirsk

L. Berdnikova

Institute of Solid-State Chemistry and Mechanochemistry of the Siberian Branch of the Russian Academy of Science

Email: a-zhdanok@mail.ru
Russia, 630128, Novosibirsk

N. Stepanova

Novosibirsk State Technical University

Email: a-zhdanok@mail.ru
Russia, 630073, Novosibirsk

M. Mikhaylenko

Institute of Solid-State Chemistry and Mechanochemistry of the Siberian Branch of the Russian Academy of Science

Email: a-zhdanok@mail.ru
Russia, 630128, Novosibirsk

Bibliografia

  1. Логинов Ю.Н. Медь и деформируемые медные сплавы. Учебное пособие. Екатеринбург: Урал. гос. техн. ун-т – УПИ, 2004. 136 с.
  2. Задруцкий П., Немененок Б.М. Производство отливок из сплавов цветных металлов. Лабораторный практикум. Минск: БНТУ, 2018. 54 с.
  3. Bustos O.C. Untersuchung zur Kornfeinung von Reinstkupfer durch chemische Zusätze und Deutung der Vorgänge. PhD Thesis. Berlin, 1990.
  4. Cziegler A., Geraseva O., Schumacher P. // Metals. 2017. V. 7. No. 9. Art. No. 383.
  5. Cziegler A.K., Schumacher P. // Int. J. Cast Met. Res. 2017. V. 30. No. 4. P. 251.
  6. Sulitsin A.V., Mysik R.K., Brusnitsyn S.V. // Solid State Phenom. 2018. V. 284. P. 357.
  7. Balart M.J., Patel J.B., Fan Z. // Int. J. Cast Met. Res. 2015. V. 28. No. 4. P. 242.
  8. Li K., McGuire M., Lupini A. et al. // ACS Appl. Nano Mater. 2020. V. 3. No. 7. P. 6863.
  9. Sundaram R.M., Sekiguchi A., Sekiya M. et al. // Royal Soc. Open Sci. 2018. No. 5. Art. No. 180814.
  10. Hannula P.M., Masquelier N., Lassila S. et al. // J. Alloys Compounds. 2018. V. 746. No. 5. P. 218.
  11. Borodianskiy K. // J. Mater. Sci. 2019. V. 54. Art. No. 13767.

Arquivos suplementares

Arquivos suplementares
Ação
1. JATS XML
2.

Baixar (1MB)
3.

Baixar (1MB)
4.

Baixar (4MB)
5.

Baixar (4MB)

Declaração de direitos autorais © Б.П. Толочко, А.А. Жданок, В.А. Кузнецов, З.А. Коротаева, Л.К. Бердникова, Н.В. Степанова, М.А. Михайленко, 2023

Este site utiliza cookies

Ao continuar usando nosso site, você concorda com o procedimento de cookies que mantêm o site funcionando normalmente.

Informação sobre cookies