Interrelation between the straw chopping length and the design of straw chopper
- Authors: Sadretdinov D.R1
-
Affiliations:
- South Ural State Agrarian University
- Issue: Vol 83, No 5 (2016)
- Pages: 42-45
- Section: Articles
- URL: https://journals.rcsi.science/0321-4443/article/view/66211
- DOI: https://doi.org/10.17816/0321-4443-66211
- ID: 66211
Cite item
Full Text
Abstract
The article deals with the process of straw chopping in straw chopper of a combine harvester. It shows the influence of straw chopper design on the straw chopping length; in particular the influence of spatial position of straw at the moment of its cutting, and of spacing of knives setting, on the chopping length. The possible variations of straw motion with chopping rotor knives after its chopping on the shearbar are described. The nature of motion of uncut straw with the chopping rotor, and the forces acting on the straw that slides over the rotor knives, are also described. The dead zone in the straw chopper is determined; it is an area between the body of chopper and the working surface of chopping rotor knives. Motion of straw in the dead zone does not lead to its chopping, because of the lack of possibility of its contact with rotor knives. The necessity of introducing of complementary units on the low wall of straw chopper body is substantiated; it leads to the intensification of straw chopping process by means of removing the straw flow from dead zone and increasing the probability of straw contact with rotor knives. The location of such units is determined. Reorientation of straw flow before and during its chopping not only reduces the straw chopping length, but also leads to the reduction of power consumed by straw chopper. This is due to both the reduction in cutting area, and the reduction in inertia of chopping rotor, because of decrease in number of knives.
Keywords
Full Text
##article.viewOnOriginalSite##About the authors
D. R Sadretdinov
South Ural State Agrarian University
Email: sadretdinov.daniil@mail.ru
Engineer Chelyabinsk, Russia
References
- Ловчиков А.П., Ловчиков В.П., Поздеев Е.А. Биологизация земледелия в ресурсосберегающих технологиях возделывания зерновых культур // Международный научно-исследовательский журнал. 2016, №1-2. С. 44-47. doi: 10.18454/IRJ.2016.43.094.
- Скорляков В.И., Юрина Т.А., Негреба О.Н. Показатели качества измельчения и разбрасывания соломы зерноуборочными комбайнами ведущих фирм // Техника и оборудование для села. 2013, №3. С. 30-33.
- Мартышов А.И., Бышов Н.В., Морозова Н.М. Показатели качества измельчения незерновой части урожая зерноуборочными комбайнами марок Дон 1500Б и Палессе GS12 // Современная наука глазами молодых ученых: достижения, проблемы, перспективы. Мат-лы межвуз. науч.-практ. конф. Рязань: РГАТУ, 2014. Ч. 1. С. 79-81.
- Родимцев С.А., Ягельский М.Ю. Оценка качества работы измельчителей зерноуборочных комбайнов // Вестник аграрной науки Дона. 2013, №1. С. 24-27.
- Пьянов В.С. Влияние комплектации зерноуборочного комбайна “Дон-1500Б” соломоуборочными средствами на основные эксплуатационные показатели его работы: Автореф. дис. … канд. техн. наук. Ставрополь, 2006. 173 с.
- Kattenstroth R., Harms H.-H., Lang T. Alignment of straw to optimise the cutting process in a combine’s straw chopper // Landtechnik. 2011, no. 5, pp. 354-357.
- Садретдинов Д.Р. Обзор технических устройств для измельчения и разбрасывания соломы зерноуборочных комбайнов // Достижения науки - агропромышленному производству: Мат-лы LIV междунар. науч.-техн. конф. Челябинск: ЧГАА, 2015. Ч. 3. С. 180-185.