Email this article Modeling the durability of diesel pistons with a crack on the edge of the combustion chamber
- Authors: Gots A.N.1, Abalyaev A.Y.1, Fomin V.M.2
-
Affiliations:
- Vladimir State University named after Alexander and Nikolai Stoletov
- Moscow Polytechnic University
- Issue: Vol 89, No 4 (2022)
- Pages: 299-306
- Section: Quality, reliability
- URL: https://journals.rcsi.science/0321-4443/article/view/125934
- DOI: https://doi.org/10.17816/0321-4443-109951
- ID: 125934
Cite item
Full Text
Abstract
BACKGROUND: During periodic long-term tests of tractor diesel engines D-240T with a combustion chamber of the CNIDI after 4000 m-hour, a deterioration in the indicators of the working process was observed. After disassembling the diesels, it turned out that the reason for this is the development of cracks on the edge of the combustion chamber (CC), and the deterioration of indicators is detected when the crack has reached a critical length.
AIMS: The aim of study is concerned investigation of a methodology for predicting of a tractor diesel piston durability with the crack on the CC edge and development of a method for calculating the crack evolution to before the transition to the improper state.
METHODS: Both experimental and computational methods were used in the research. Experimental pistons was manufactured with some design changes: the radius of the edge rounding changed, which changed the thickness of the side wall of the CC.
RESULTS: Motor studies of diesel engines have shown that with a certain piston design, a crack either does not appear at all, or appears after a large number of cycles. Additional computational studies have shown that the crack development depends on the stress intensity coefficient at the crack tip. Using the data of experimental studies, a method has been developed for estimating the critical crack length in the edge of the CC, at which the intensity of stresses in the vicinity of its vertex exceeds the limits accepted for this material from which the piston is made.
CONCLUSIONS: A method for calculating the durability of the piston during the development of a crack on the edge of the combustion chamber is proposed. Verification of the calculated data obtained during the numerical implementation of the piston evaluation method using the example of the diesel piston D-240 showed that for a range of crack lengths up to 1 mm and operating time over 7000 m-hour, the calculation error com-pared to the operational test data does not exceed 11%.
Keywords
Full Text
##article.viewOnOriginalSite##About the authors
Alexander N. Gots
Vladimir State University named after Alexander and Nikolai Stoletov
Email: hotz@mail.ru
ORCID iD: 0000-0002-5236-8304
SPIN-code: 9324-7215
Professor, Dr. Sci. (Tech.)
Russian Federation, VladimirAndrey Yu. Abalyaev
Vladimir State University named after Alexander and Nikolai Stoletov
Author for correspondence.
Email: ice_aya@bk.ru
ORCID iD: 0000-0003-0590-321X
SPIN-code: 2180-2769
Cand. Sci. (Tech.), Head of the Department
Russian Federation, VladimirValery M. Fomin
Moscow Polytechnic University
Email: mixalichDM@mail.ru
SPIN-code: 7556-3336
Professor, Dr. Sci. (Tech.)
Russian Federation, MoscowReferences
- Rozhansky VA, Kukharenok GM. Influence of combustion chamber parameters on the performance of the D-240 diesel engine // Traktory i selkhozmashiny. 1974;9:11–12. (in Russ).
- Voinov AN. Combustion in high-speed piston engines. Izd. 2-e, pererab. dop. Moscow: Mashinostroenie; 1977. (in Russ).
- Ivanchenko AB. Metodika otsenki termoustalostnoy prochnosti porshney forsirovannykh dizeley [dissertation]. Moscow; 1995. (in Russ).
- Rumb VK, Medvedev VV. Forecasting the durability of marine diesel parts. Dvigatelestroenie. 2006;4:29–34. (in Russ).
- Donchenko AS, Morganyuk VS, Averchenkov EA, et al. Calculation of the stress-strain state of a tractor diesel piston under cyclic loading. Problemy prochnosti. 1983;3:39–44. (in Russ).
- Gots AN, Glinkin SA. Loading conditions for pistons of internal combustion engines and the causes of cracking on the edge of the combustion chamber. Tractors and agricultural machinery. 2016;10:25–29. (in Russ).
- Shekhovtsov AF, Abramchuk FI, Pylev VA. Creep and tensile relaxation of aluminum alloy AL25. Dvigatelestroenie. 1986;11: 45–47. (in Russ).
- Gots AN, Glinkin SA. Forecasting the durability of pistons of internal combustion engines. Balti: Lambert Academic Publishing; 2017. (in Russ).
- Morozov EM, Nikishkov GP. Finite element method in fracture mechanics. Moscow: Nauka; 1980. (in Russ).
- Pospisil B, Kvitka AL, Tretyachenko GN, et al. Strength and durability of elements of power equipment. Kiev: Naukova. Dumka; 1987. (in Russ).
- Birger IA. Deterministic and statistical models of durability. In: Problems of aircraft reliability. Obraztsova IF, Volmira AS. (eds). Moscow: Mashinostroenie; 1980. (in Russ).
Supplementary files
