Modeling the Influence of Nanosized Fillers on the Mechanical Properties and Wear Resistance of a Composite Based on Polyether Ether Ketone
- Autores: Li S.1, Sedakova E.2
-
Afiliações:
- Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russia
- Institute for Problems in Mechanical Engineering, Russian Academy of Sciences, St. Petersburg, Russia
- Edição: Nº 3 (2023)
- Páginas: 64-69
- Seção: НАДЕЖНОСТЬ, ПРОЧНОСТЬ, ИЗНОСОСТОЙКОСТЬ МАШИН И КОНСТРУКЦИЙ
- URL: https://journals.rcsi.science/0235-7119/article/view/137588
- DOI: https://doi.org/10.31857/S0235711923030100
- EDN: https://elibrary.ru/PQKLXD
- ID: 137588
Citar
Resumo
The method of molecular-dynamic modeling was applied for creating models of polyether ketone and two of its nanocomposites with fillers in the form of copper nanoparticles and with fullerene. The results of comparative study of the deformation-strength properties of these materials by means of uniaxial tension at a constant strain rate are presented. It was obtained that, when filling polyether ketone with fullerene, the elasticity value of the composite decreases by approximately two times, and in the case of filling of the same matrix with copper nanoparticles, its value increases by approximately 30%. At the same time, the average energy of intermolecular bonds of the composite with copper nanoparticles is 2.65 times greater than that of the composite with fullerene.
Sobre autores
S. Li
Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russia
Email: elenasedakova2006@yandex.ru
Россия, Санкт-Петербург
E. Sedakova
Institute for Problems in Mechanical Engineering, Russian Academy of Sciences, St. Petersburg, Russia
Autor responsável pela correspondência
Email: elenasedakova2006@yandex.ru
Россия, Санкт-Петербург
Bibliografia
- Кисель Ю.Е., Кравченко И.Н., Купреенко А.И. и др. Влияние прочности компонентов композиционных материалов на их физико-механические свойства // Проблемы машиностроения и надежности машин. 2021. № 6. С. 43.
- Лялякин В.П., Аулов В.Ф., Ишков А.В. и др. Свойства износостойких композиционных покрытий, полученных скоростным борированием // Проблемы машиностроения и надежности машин. 2022. № 2. С. 47.
- Atkinson J.R., Hay J.N., Jenkins M.J. Enthalpic Relaxation in Semi-crystalline PEEK // Polymer. 2002. V. 43 (3). P. 731.
- Moby V., Dupagne L., Fouquet V. et al. Mechanical Properties of Fused Deposition Modeling of Polyetheretherketone (PEEK) and Interest for Dental Restorations: A Systematic Review// Materials. 2022. V. 15 (19). P. 6801.
- Frankland S.J.V., Harik V.M., Odegard G.M et al. The stress strain behavior of polymer nanotube composites from molecular dynamics simulation // Compos. Sci. Technol. 2003. V. 63. P. 1655.
- Sun H., Jin Z., Yang C. et al. COMPASS II: extended coverage for polymer and drug-like molecule databases // J. Mol. Model. 2016. V. 22 (2). P. 47.
- Song J., Lei H., Zhao G. Improved mechanical and tribological properties of polytetrafluoroethylene reinforced by carbon nanotubes: A molecular dynamics study // Computational Materials Science. 2019. № 168. P. 131.
- Arun K., Subramaniyan C.T. Sun. Continuum interpretation of virial stress in molecular simulations // Int. J. of Solids and Structures. 2008. V. 45 (14–15). P. 4340.
- Najeeb S., Zafar M.S., Khurshid Z., Siddiqui F. Applications of polyetheretherketone (PEEK) in oral implantology and prosthodontics // J. of Prosthodontic Research. 2016. V. 60 (1). P. 12.
- Ли С., Седакова Е.Б. Применение метода молекулярно-динамического моделирования для анализа износостойкости композита в сравнении с исходной полимерной матрицей // Вопросы материаловедения. 2022. № 1 (109). С. 1.
- Ли С., Седакова Е.Б. Молекулярное моделирование кинетики поверхностного разрушения полимерных композитов на примере Ф4К20 // Трение и износ. 2022. Т. 43. № 6. С. 612.
- Гинзбург Б.М., Возняковский А.П., Евлашенко С.И., Точильников Д.Г. РФ Патент 2378297. Антифрикционный полимерный материал, 2010.
- Savagatrup S., Makaram A.S., Burke D.J. et al. Mechanical properties of conjugated polymers and polymer fullerene composites as a function of molecular structure // Advanced Functional Materials. 2014. V. 24 (8). P. 1169.
- Kim J.H., Noh J., Choi H. et al. Mechanical Properties of Polymer–Fullerene Bulk Heterojunction Films: Role of Nanomorphology of Composite Films // Chemistry of Materials. 2017. V. 29 (9). P. 3954.
- Molefi J.A, Luyt A.S., Krupa I. Comparison of the influence of copper micro-and nano-particles on the mechanical properties of polyethylene/copper composites // J. of Materials Science. 2010. V. 45 (1). P. 82.
- Harandi M.H., Alimoradi F., Rowshan G. et al. Morphological and mechanical properties of styrene butadiene rubber/nano copper nanocomposites // Results in physics. 2017. V. 7. P. 338.
- Песецкий С.С., Богданович С.П., Мышкин Н.К. Триботехнические свойства нанокомпозитов, получаемых диспергированием наполнителей в расплавах полимеров // Трение и износ. 2007. Т. 28. № 5. С. 500.